LEAF 2021

Prices and Supplies are subject to change without notice CUSTOMER SERVICE 1-262-763-4087 FAX 1-262-763-1920 ROTAX ® 912 UL, 912 ULS, 914 UL 61 Fig. No. Part No. Description 912 UL 912 ULS 914 UL 2 842 655 Heli-Coil Thread Insert M8x20 2 2 2 3 924 451 Oil Tube 1 1 1 4 929 951 Dowel 10.8X25 5 5 5 5 929 845 Pin D8x20 1 1 1 6 840 191 Stud M8x105 1 1 1 7 944 222 Blinding Shim 1b 1b 1b 8 430 061 O-Ring 26.7x1.8 1b 1b 1b 9 850 902 O-Ring 9X2 2 2 2 10 944 131 Washer 8 8f 8f 7f 11 840 061 Allen Screw M8x80 1 1 1 12 840 091 HexCollar Screw M8x140-SW10 1 1 1 13 840 101 Hex Collar Screw M8x150-SW10 2 2 2 14 940 071 Hex Collar Screw M8x45-SW10 2 2 2 15 440 406 Hex Collar Screw M8x65-SW10 1 1 1 16 842 476 Collar Cap Nut M8 1 1 1 17 945 751 Lock Washer A6 9 9 9 17 827 962 Washer 6.4 9 9 9 18 840 887 Allen Screw M6x30 9 9 9 19 227 280 Thrust Washer 1 1 1 20 940 316 Countersunk Screw M5x12 1 1 1 21 941 487 Allen Screw M10x110 1 1 1 21 941 557 Allen Screw M10x150 (1) (1) 22 945 833 Lock Washer A10 1 1 1 23 927 410 Washer 10.5 1 1 1 Fig. No. Part No. Description 912 UL 912 ULS 914 UL 24 933 872 Plain Bearing “C” 6cf 6cf 6cf 24 933 873 Plain Bearing “D” 6df 6df 6df 25 933 335 Ring Half 2 2 2 26 831 929 O-Ring 5x2 1 1 1 27 840 141 Stud M8x186 8 8 8 28 840 171 Stud M8x200 8 8 8 29 431 570 O-Ring 10.82x1,78 8i 8i 8i 29 431 411 Gasket ARh ARh ARh 30 942 302 Collar Nut M8 8j 8j 8j 31 842 476 Collar Cap Nut M8 8j 8j 8j 32 440 686 Hex Collar Screw M8x130 1 1 1 33 840 131 Stud M8x138 2 2 2 34 929 116 Thread Sleeve M8 8 8 8 35 950 141 Gasket Ring A 8X13 1 1 1 36 240 072 Allen Screw M8x20 1 1 1 37 440 107 Allen Screw M8x50 - - 1f 38 xxx xxx See Engine Suspension Frame, page 55 - - 1 39 926 401 Washer 8.4/15/1 - - AR 39 926 402 Washer 8.4/15/1.5 - - AR 40 881 120 Screw Set, Crankcase 1f 1f 1f AR - As required a - Marked with S/N, b - Only for model 2 and 4, c - Tolerance group “C” 1.820 - 1.829 MM, d - Tolerance group “D” 1.830 - 1.839 MM, e - Depending on con fi guration use 14 studs part no. 840 752 M8x201 or 8 studs M8x201 and 6 studs part no. 840 754 M8x210, f - See Overhaul Manual of the respective engine type, current issue, g - Only for use with new cylinders 913 221 with countersunk. With the cylinder 913 225 the countersunk was already introduced starting from beginning of the production, h - Following Service Instruction has to be noticed: SI-912-019 current issue, SI-914-021, i - 431 570 introduced as per engine S/N as follows: 912 UL: S/N 06,770.893, 914 UL: S/N 07,682.596, 912 ULS: S/N 06,781.191, j - Wrench size A/F 11 CRANKCASE - FROM S/N 06.0010 up to 14,2384